Menu
entries per page
1 – 20 / 515
Gas pressure test case gas HANS
new
Gas pressure test case gas HANSIncluded: – rugged outdoor case with foam insert – testhead HANS 2 1/2″ ext. thread, Pmax: 60 bar – two hook spanner 95-100 mm – special o-ring-grease approximatly 20g – filling hose air DN16 x 1m – Adapter ventilation with sound insulation
new
Adapter S5020N-T5010K-T5010K with ball valve
new
Adapter S5020N-T5010K-T5010K with ball valveOptional additional part to the Test head HEINZ for carrying out water pressure tests according to W400-2. The pressure hose of the pump and an EDS2-V can be connected to the HEINZ at the same time via the T-piece. Connections: T-piece With nipple Series 5020 (Series 5000) and 2x coupling Series T 5010 with ball valve (Series 5000)
T-connector C25N-C25C-C25C
new
T-connector C25N-C25C-C25CT-connector with camlock connections for parallel operation of two devices of Mobile Gas Flare M max. pressure 16 bar
Control panel for Mobile Gas Flare M
new
Control panel for Mobile Gas Flare MConnection adapter 1 inch external thread, including pressure reducer and integrated valve for connecting the Mobile Gas Flare M to gas pipes. – Integrated pressure reducer for restricting the inlet pressure at the mobile gas flare (max. 1bar) – integrated valve for safe gas inlet and flow restriction – Series 21 coupling and screw coupling for connecting a pressure or concentration measuring device – 1″ ET on the inlet side, Camlock coupling DN25 on the outlet side – max. pressure 16 bar
Adapter DN claw coupling to S5020N
new
Adapter DN claw coupling to S5020NClaw coupling with connecting nipple series 5020
Pressure test case W 400-2
new
Pressure test case
W 400-2Sturdy case with foam insert for accessories for tests according to W 400-2. The scope of delivery includes the following items: – 1x test head HANS – 2x hook spanner – Special O-ring grease – 1x hose Hyd16 2m Geka-S5020N In the foam insert there is also space for the following optional items: 1x EDS2-V 1-42l/min 1x EDS2-V 4-160 l/min 1x control manometer 10 bar 1x control manometer 25 bar 1x Flow reducer DWZ/EDS2-V
GasCar Laser HUNTER standard
new
GasCar Laser HUNTER standardPump unit for use with a Laser HUNTER. Possibility to clean the suction system by backwashing using an integrated compressor. Additional components are required for a functional system for vehicle-based pipeline inspection and must be ordered separately: – Laser HUNTER (item 251220). – Intake unit & probes – Accessories, e.g. hoses – Test system – Notebook, notebook holder – GIS software (Esders PI NOTE) – GPS Receiver
Suction System GasCar Laser HUNTER
new
Suction System GasCar Laser HUNTERSuction system for fixed integration into the front apron of the vehicle. The required bell probes or hose probes can be easily mounted via quick-release couplings and must be ordered separately. Depending on the vehicle, additional accessories (small parts, etc.) may be required to install the system and will be charged separately. Likewise, the installation will be charged additionally according to the time required.
Adapter DN15C to 2x DN15C
new
Adapter DN15C to 2x DN15CCompressed air manifold DN15 with claw coupling and ball valve on the inlet side, 2 outlets with claw coupling on the outlet side for simultaneous pressurisation of pipelines, e.g. for tests according to FW 602. Max. pressure: 16 bar
Hose Hyd16 2m Geka-S5020N
new
Hose Hyd16 2m Geka-S5020N– drain hose for use with the test head HANS and EDS2-V – nominal diameter DN16 for low pressure loss and optimal flow rate – Geka coupling on one side, nipple S 5020 on the other side
GasCar Laser HUNTER plus
new
GasCar Laser HUNTER plusPump unit for use with two Laser HUNTERs for separate intake and analysis of the gas flow via the left and right side of the vehicle. Possibility to clean the suction system by backwashing using an integrated compressor. Additional components are required for a functioning system for vehicle-based pipe network inspection and must be ordered separately: – 2x Laser HUNTER (item 251220). – intake unit & probes – accessories, e.g. hoses – test system – notebook, notebook holder & software – GIS software (Esders Pi NOTE) – GPS receiver
Adapter C25C to 1 inch with O-ring seal
new
Adapter C25C to 1 inch with O-ring sealAdapter for the Mobile Gas Flare M for use in hard-to-reach blow-out units. Connections: inlet side 1″ ET with O-ring, outlet side Сamloсk coupling DN25 Gas hose DN25 with Сamloсk nipple can be connected directly. Max. pressure 16 bar
Adapter S5020N to T2510C
new
Adapter S5020N to T2510CAdapter for use of HEINZ accessories (nipple series 2500) with test head HANS (coupling series 5000) Nipple Series 5020 to coupling Series T 2510
Hose NBR25 K25N-K25K 5 meters
new
Hose NBR25 K25N-K25K 5 metersgas hose, length 5 m for Mobile Gas Flare M NBR, both sides Camlock Adapter. Coupling DN 25 on one side, nipple DN 25 on the other, max. pressure 16 bar
Schlauch NBR25 K25N-K25K 10 meters
new
Schlauch NBR25 K25N-K25K 10 metersgas hose, length 10 m for Mobile Gas Flare M NBR, both sides Camlock Adapter. Coupling DN 25 on one side, nipple DN 25 on the other, max. pressure 16 bar
Hose NBR 3m S2520N-claw
new
Hose NBR 3m S2520N-clawPressure hose, gas resistant, length 3 m, NBR DN13, one side nipple series 2520, other side claw coupling, max. pressure 16 bar For pressurising pipelines via test specimen HEINZ
Adapter ventilation with sound insulation
new
Adapter ventilation with sound insulationwith nipple series 5020 can be used with test body HANS
E-Scooter Laser HUNTER
new
E-Scooter Laser HUNTERE-Scooter Ninebot MAX G30D II with mounted carpet probe for professional gas leak detection Filter and hose for connection to measuring device Laser HUNTER are included. The use of the scooter in German road traffic is subject to compulsory insurance! The corresponding registration of the scooter is not part of the scope of delivery, but is the responsibility of the customer (and the rules and regulations of the country you reside in). The Laser HUNTER is not part of the scope of delivery either and must be ordered separately.
Test head HANS stainless steel OT 2 1/2″
new
Test head HANS stainless steel OT 2 1/2"P max: 60 bar and equipped with quick couplings and protective caps. In contrast to the HEINZ specimen, this specimen has two ball valves with quick couplings 5010 and one quick coupling 2510 without ball valve. A screw coupling -VA- is provided for connecting an external pressure sensor of the smart memo.
entries per page
1 – 20 / 515
keyboard_arrow_up