Connection accessories - Esders GmbH

Menu

Category

Search

entries per page

1 – 20 / 512

Suction System GasCar Laser HUNTER

Suction System GasCar Laser HUNTER

Suction system for fixed integration into the front apron of the vehicle. The required bell probes or hose probes can be easily mounted via quick-release couplings and must be ordered separately. Depending on the vehicle, additional accessories (small parts, etc.) may be required to install the system and will be charged separately. Likewise, the installation will be charged additionally according to the time required.

Hose NBR 3m S2520N-claw

Hose NBR 3m S2520N-claw

Pressure hose, gas resistant, length 3 m, NBR DN13, one side nipple series 2520, other side claw coupling, max. pressure 16 bar For pressurising pipelines via test specimens e.g. for tests according to German guideline FW602 (district heating)

Adapter C25C to 1 inch with O-ring seal

Adapter C25C to 1 inch with O-ring seal

Adapter for the Mobile Gas Flare M for use in hard-to-reach blow-out units. Connections: inlet side 1″ ET with O-ring, outlet side Сamloсk coupling DN25 Gas hose DN25 with Сamloсk nipple can be connected directly. Max. pressure 16 bar

Adapter S5020N-T5010K-T5010K with ball valve

Adapter S5020N-T5010K-T5010K with ball valve

Optional additional part to the Test head HEINZ for carrying out water pressure tests according to W400-2. The pressure hose of the pump and an EDS2-V can be connected to the HEINZ at the same time via the T-piece. Connections: T-piece With nipple Series 5020 (Series 5000) and 2x coupling Series T 5010 with ball valve (Series 5000)

Connection adapter 1 inch external thread via pressure reducer and integrated slider to Camlock coupling DN 25 for connecting the Mobile Gas Flare M to gas pipes. – Integrated pressure reducer for restricting the inlet pressure at the mobile gas flare – integrated slide valve for safe gas inlet and flow restriction – Series 21 coupling and screw coupling for connecting a pressure or concentration measuring device – 1″ ET on the inlet side, Camlock coupling DN25 on the outlet side – max. pressure 16 bar

E-Scooter Laser HUNTER

E-Scooter Laser HUNTER

E-Scooter Ninebot MAX G30D II with mounted carpet probe for professional gas leak detection Filter and hose for connection to measuring device Laser HUNTER are included. The use of the scooter in German road traffic is subject to compulsory insurance! The corresponding registration of the scooter is not part of the scope of delivery, but is the responsibility of the customer (and the rules and regulations of the country you reside in). The Laser HUNTER is not part of the scope of delivery either and must be ordered separately.

Adapter DN15C to 2x DN15C

Adapter DN15C to 2x DN15C

Compressed air manifold DN15 with claw coupling and ball valve on the inlet side, 2 outlets with claw coupling on the outlet side for simultaneous pressurisation of pipelines, e.g. for tests according to FW 602. Max. pressure: 16 bar

Hose Hyd16 2m Geka-S5020N

Hose Hyd16 2m Geka-S5020N

– drain hose for use with the test head HANS and EDS2-V – nominal diameter DN16 for low pressure loss and optimal flow rate – Geka coupling on one side, nipple S 5020 on the other side

GasCar Laser HUNTER dual

GasCar Laser HUNTER dual

Pump unit for use with two Laser HUNTERs for separate intake and analysis of the gas flow via the left and right side of the vehicle. Possibility to clean the suction system by backwashing using an integrated compressor. Additional components are required for a functioning system for vehicle-based pipe network inspection and must be ordered separately: – 2x Laser HUNTER (item 251220). – intake unit & probes – accessories, e.g. hoses – test system – notebook, notebook holder & software – GIS software (Esders Pi NOTE) – GPS receiver

Adapter S5020N to T2510C

Adapter S5020N to T2510C

Adapter for use of HEINZ accessories (nipple series 2500) with test head HANS (coupling series 5000) Nipple Series 5020 to coupling Series T 2510

Pressure test case W 400-2

Pressure test case
W 400-2

Sturdy case with foam insert for accessories for tests according to W 400-2. The scope of delivery includes the following items: – 1x test head HANS – 2x hook spanner – Special O-ring grease – 1x hose Hyd16 2m Geka-S5020N In the foam insert there is also space for the following optional items: 1x EDS2-V 1-42l/min 1x EDS2-V 4-160 l/min 1x control manometer 10 bar 1x control manometer 25 bar 1x Flow reducer DWZ/EDS2-V

Test head HANS stainless steel OT 2 1/2″

Test head HANS stainless steel OT 2 1/2"

P max: 60 bar and equipped with quick couplings and protective caps. In contrast to the HEINZ specimen, this specimen has two ball valves with quick couplings 5010 and one quick coupling 2510 without ball valve. A screw coupling -VA- is provided for connecting an external pressure sensor of the smart memo.

GasCar Laser HUNTER single

GasCar Laser HUNTER single

Pump unit for use with a Laser HUNTER. Possibility to clean the suction system by backwashing using an integrated compressor. Additional components are required for a functional system for vehicle-based pipeline inspection and must be ordered separately: – Laser HUNTER (item 251220). – Intake unit & probes – Accessories, e.g. hoses – Test system – Notebook, notebook holder – GIS software (Esders PI NOTE) – GPS Receiver

Test head HUGO 1″ ext. thread

Test head HUGO 1" ext. thread

Test head with 3 plugs for pressure measurement instrument, pressure gauge and compressor or handpump. – with spare O-ring – P max: 10 bar

Carbon probe set T-handle

Carbon probe set T-handle

T-bone handle screwable pinhole and bell probe combination

Adaptation case aqua

Adaptation case aqua

Adaptation case aqua Included: – rugged outdoor case with foam insert – testhead HEINZ 2 1/2″ ext. thread, Pmax: 60 bar – two hook spanner 95-100 mm – special o-ring-grease approximatly 20g – water drain hose DN8 x 3m

Flexible quick connection probe V3 with filter head

Flexible quick connection probe V3 with filter head

– goose neck length 255 mm – can be connected to the gas inlet of the measurement device via quick coupling

Carpet probe TS14 with joint

Carpet probe TS14 with joint

with flexible joint unit Carpet probe with optimised suction area, highly flexible hose with coupling and telescopic handle. The warranty of the carpet mat is 3 years.

entries per page

1 – 20 / 512