Products
Gas venting pipes Standpipe flange DN 50, stainless
Standpipe flange DN 50, stainless – 402079
Standpipe flange DN 50, stainless
Standpipe flange DN 50, stainless for pressure tests with testhead
int. thread G 2 1/2″
– Separate feed via Storz C for filling
with shut-off via ball valve
– sampling valve
– a 50cm long standpipe extension with standpipe foot DN 50
(System Baden-Württemberg) can be screwed on.
Prices for customers after registration
1
Article affiliation:
Test pump MPP 28-25
Test pump MPP 28-25 Pressure range 0 – 25 bar
– practice-oriented test pumps with electronic control unit
for the simplified performance of compression tests pursuant
to EN 805 (W 400-2 in Germany)
– automatic pressure stabilisation for preset test pressure which
can be programmed in steps of 0.1 bar into the control unit
– high delivery capacity rate of 28 l/min enable the generation
of the required test pressure in less than 10 minutes, as required
by the contraction procedure
technical data:
– connection value: 230 V / 400 V 50 Hz
– power consumption: 2.200 VA
– protection type: IP 54
– max. test pressure 25 bar
– test pressure: 0 to 25 bar in steps of 0.1 bar
– safety: safety valve
– delivery volume: 28 l/min
– decompression: automatic / manual
– GSM-remote monitoring: optional
Test pump MPP 68-25
Test pump MPP 68-25 Pressure range 0 – 25 bar
– practice-oriented test pumps with electronic control unit
for the simplified performance of compression tests pursuant
to EN 805 (W 400-2 in Germany)
– automatic pressure stabilisation for preset test pressure which
can be programmed in steps of 0.1 bar into the control unit
– high delivery capacity rate of 68 l/min enable the generation
of the required test pressure in less than 10 minutes, as required
by the contraction procedure
technical data:
– connection value: 400 V 50 Hz
– power consumption: 4.000 VA
– protection type: IP 54
– max. test pressure 25 bar
– test pressure: 0 to 25 bar in steps of 0.1 bar
– safety: safety valve
– delivery volume: 68 l/min
– decompression: automatic / manual
– GSM-remote monitoring: optional
Test pump MPP 68-35
Test pump MPP 68-35 Pressure range 0 – 35 bar
– practice-oriented test pumps with electronic control unit
for the simplified performance of compression tests pursuant
to EN 805 (W 400-2 in Germany)
– automatic pressure stabilisation for preset test pressure which
can be programmed in steps of 0.1 bar into the control unit
– high delivery capacity rate of 68 l/min enable the generation
of the required test pressure in less than 10 minutes, as required
by the contraction procedure
technical data:
– connection value: 400 V 50 Hz
– power consumption: 5.000 VA
– protection type: IP 54
– max. test pressure 35 bar
– test pressure: 0 to 35 bar in steps of 0.1 bar
– safety: safety valve
– delivery volume: 68 l/min
– decompression: automatic / manual
– GSM-remote monitoring: optional
Test pump MPP 11
Test pump MPP 11 Pressure range 0 – 25 bar
full automatic testing pump for pressure build-up and pressure holding adjusted
without pressure impulses
technical data:
– connection value: 230 V 50 Hz
– power consumption: 1.850 VA
– protection type: IP 54
– max. test pressure 25 bar
– test pressure: 0 to 25 bar in steps of 0.1 bar
– safety: safety valve
– delivery volume: 11 l/min. Maximum output approx. 300 l
until automatic switch off, limited by temperature.
– decompression: manual
– Geka connection for water connection
– quick coupling for pressure-side connection